# Experiment Setup

## Vial Setup

{% hint style="info" %}
Levels of liquid in the vials are set by the height of the efflux needle.
{% endhint %}

Needles used were all 16ga

Reservoir volume = 30 mL

* Efflux needle = 3" needle in the tallest vial cap port
* Media in = 2" needle in the shortest port
* Vial to Vial = 3" needle in the *second* tallest port

Lagoon volume = 10 mL

* Efflux needle = 4" needle in the *second* tallest vial cap port
* Vial to Vial = 3" needle in the lowest port
* Inducer = 4" needle in the tallest port or 2" needle in the second lowest

{% hint style="info" %}
To have high accuracy when using the low volume pumps it is important to avoid individual drops. Therefore we want needles to abut inside of the vials to get a constant stream of fluid when pumping.
{% endhint %}

<figure><img src="/files/6JA7YPP1zpX7mfeBpaZK" alt=""><figcaption><p>Vials set up for reservoir (left) and lagoon (right).</p></figcaption></figure>

## Fluidic Lines

Hook up pump lines in the configuration shown below

<figure><img src="/files/tYoDLe1awB9AuGR6VI0g" alt=""><figcaption></figcaption></figure>

<figure><img src="/files/cXWW5rw3fzScaodmEK54" alt=""><figcaption></figcaption></figure>

## Alter Settings in custom\_script.py

1. Copy the whole ePACE template folder (`/dpu/experiment/epace-template/`)
2. Rename the copied folder to your experiment name
3. Change the `EVOLVER_PORT` to your eVOLVER's port
4. Alter `USER DEFINED VARIABLES` using the guide below:

<figure><img src="/files/xXPHPKQPfqTjhDpOva1O" alt=""><figcaption><p>ePACE user defined variables as of 2023-11-20</p></figcaption></figure>

### `lower_thresh` and `upper thresh`

* The lower and upper OD threshold of the turbidostat that is running on the reservoir vial
* Format: `[vial 0, vial 1]`

### `start_time`&#x20;

* chemostats will not pump until this amount of hours has elapsed
* Useful to allow cells in reservoir to grow up before starting experiment

### `rate_config`

* Format: `rate_config = [reservoir, lagoon]`
* In vial volumes per hour (V/h)

#### For the Reservoir

* Replaces volume in turbidostat that is removed via vial to vial
* Must be greater than the volume you are taking out
* Turbidostat controls will separately preventing reservoir from increasing in OD too much
* Do not set too high or your cells will be unable to grow fast enough and wash out

#### For the Lagoon

* Set based off of phage replication rate

#### Example Settings:

1. If you have a 30mL reservoir and 10mL lagoon
2. Setting to `rate_config = [1, 1]`
   1. 30mL media into reservoir and 10mL from reservoir into lagoon per hour
3. Setting to `rate_config = [0.4, 1.2]`
   1. If we set lagoon rate to 1.2 V/h, we should not set reservoir rate to lower than 0.4 V/h to avoid draining the reservoir
   2. 1.2 V/h \* 10mL = 12mL/h into lagoon
   3. 0.4 V/h \* 30mL = 12mLh into reservoir

### Inducer

`inducer_on`

* Turn inducer off to start (`inducer_on = False`)
* Wait for host cells to grow up before starting induction (`inducer_on = True`) and inoculating with phage

`inducer_concentration`

* Times greater (X) the concentration of your inducer in its bottle compared to its final concentration in the lagoon
* Format `[pump 5, pump 6]`

#### For example:

1. Your arabinose stock is 1 M
2. The final lagoon concentration you want is 10 mM
3. Therefore 1000 mM / 10 mM = 100 X your final concentration
4. If you are not using another inducer, `inducer_concentration` `= [100, 0]`

## Optional Settings

*You do not need to alter these settings*

### Swapping Lagoon and Reservoir Vials

If you do want to alter these variables, you also need to swap the vial locations in the turbidostat and chemostat settings of:

* `lower_thresh` and `upper thresh`
* `rate_config`

#### `reservoir_vial`&#x20;

* Vial number of host cell reservoir
* It is a turbidostat *and* a chemostat. Read why [here](/evolver/extensions/min-evolver/epace-with-min-evolver.md#experimental-overview).

#### `lagoon_vial`&#x20;

* Vial number of lagoon
* Only a chemostat, can have up to two inducers&#x20;


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://khalil-lab.gitbook.io/evolver/extensions/min-evolver/epace-with-min-evolver/experiment-setup.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.